Visualizzazione stampabile
ragazzi, io sono super niubbo di se cose.
alla fine della giostra esiste un bolt rinforzato di quelche genere per il vfc?
se esiste mettete na foto, marca e modello che me lo procuro?
leggendo in giro mi sembrava di aver capito che il wa po diventarlo previa qualche modifica...o ho capito male?
Ti ho detto il Parity Bolt per Prime(88$), lo trovi da TMC.Quote:
Originariamente inviata da TEX_ZEN
First things first:
Bolt carrier did need modification, luckily i used to be a fabricator and had my grinder and fabricating tools handy.
When i had measured the RA-TECH bolt carrier to the origional VFC bolt carrier it was about 3mm longer so i had to grind that down flush, i also had to do the modification to the bolt itself as explained on the youtube video that RA-TECH showed.
I had to sand the inside of the upper receiver for a smoother action.
There was a few more mods i needed to do to it but its hard to explain. As soon as my brother brings up my camera tonight or tomorrow i will post pictures of the mods i carried out for it to fit.
On a good note it does work now but i havnt got a chrono so i cant do any power tests yet.
Also if you go for a steel bolt carrier i would suggest that you purchase an enhanced recoil spring to make it a bit more snappy.
All i can say is that it is doable and well worth it https://www.arniesairsoft.co.uk/foru...ault/smile.gif
Pics up soon and i will be happy to help anyone who is going down the same road.
---------- Post added at 22:17 ---------- Previous post was at 22:16 ----------
After a little more sanding inside the upper receiver the bolt has become more free so the recoil is fast and snappy https://www.arniesairsoft.co.uk/foru...lt/biggrin.gif
All i need to do now is test the power adjustment and make sure thats fine and dandy.
I think now the wholt BCG has been changed this will allow me to use WA, pro win and G&P mags because the loading tab on the RA-TECH bolt is smaller than the standard VFC.
---------- Post added at 22:18 ---------- Previous post was at 22:17 ----------
https://i1000.photobucket.com/albums...DSC02856-1.jpg
---------- Post added at 22:19 ---------- Previous post was at 22:18 ----------
MOD 1 - as on RA-TECHS youtube video.
https://i1000.photobucket.com/albums...s/DSC02834.jpg
---------- Post added at 22:20 ---------- Previous post was at 22:19 ----------
MOD 2 - grind down the edge of the bolt by about 1.5mm, aslo grind the base so the hammer isnt put under to much stress.
https://i1000.photobucket.com/albums...s/DSC02835.jpg
E così ti sei fottuto tutto il vantaggio di avere i migliori caricatori GBB sul mercato, che costano poco funzionano bene e non perdono gas.Quote:
Originariamente inviata da Allen
;)
Chi è il furbastro?
mod 3 - round of the circled part so the hammer doesnt get damaged. also creates a much smoother action.
mod 4 - grind down to match the VFC bolt and give the hammer enough room to fire.
https://i1000.photobucket.com/albums...s/DSC02830.jpg
---------- Post added at 22:22 ---------- Previous post was at 22:21 ----------
mod 5 - grind down the back of the bolt carrier to match the length of the VFC bolt carrier so it can sit in the receiver properly
https://i1000.photobucket.com/albums...s/DSC02833.jpg
---------- Post added at 22:23 ---------- Previous post was at 22:22 ----------
i also sanded the inside of the upper receiver with some wet and dry sandpaper to give the new bolt carrier enough room to move freely but it now sits in much better than the origional VFC bolt carrier with no rattles.
https://i1000.photobucket.com/albums...s/DSC02861.jpg
---------- Post added at 22:24 ---------- Previous post was at 22:23 ----------
https://i1000.photobucket.com/albums...s/DSC02857.jpg
---------- Post added at 22:27 ---------- Previous post was at 22:24 ----------
queste ultime modifiche riguardano il HK416 (sabbiatura dell' interno gusci), da notare il finto recupero del gas tagliato per alloggiare il carrello della ra-tech
---------- Post added at 22:28 ---------- Previous post was at 22:27 ----------
uno su arniesairsoft
---------- Post added at 22:28 ---------- Previous post was at 22:28 ----------
uno su arniesairsoftQuote:
Originariamente inviata da Wotan
io mi tengo il mio vfc così comè
Beh certo che se ci fosse un carrello in acciaio anche per il vfc si risolverebbe il problema principale...Quote:
Originariamente inviata da Allen
live, non prendertela ma è tutta roba nuova per me...oltre al fatto di non capire proprio cosi bene l'inglese:)
mi sembra di aver capito che la RAT offre dei carrelli sostitutivi per diverse marche di gbb, quello che interessa a noi è il prime che ho trovato da tmc...e fin qua ci siamo.
ora pero vorrei capire se le modifiche postate da allen si riferiscono al carrello per wa o al prime.
il prime si monta e basta o va modificato?
il loading vfc sul prime lavora o bisogna perforza usare quello RAT?
Prendermela? Per cosa?Quote:
Originariamente inviata da TEX_ZEN
Ti ricordi il commento che ho quotato nella pagina precendente?
P.S: sono in questo campo solo da febbraio ;)Quote:
if you need to use it directly for VFC M4 gbb,
you could use our complete bolt for Prime
@Allen: che carrier è? Parity o CNC?
quindi il bolt completo sul vfc funziona senza modifiche... ma poi i caricatori vfc funzionano?
stavo pensando che se completo va significa che la differenza sta nel Loading e non nel carrello in se...
Non so cosa pensare. TMC ha contattato per me quei froci della Ra-Tech visto che non mi rispondevano.Quote:
Originariamente inviata da TEX_ZEN
Riposta:
E che cazzo, allora cosa scrivono a fare che si può mettere??!! :SQuote:
Thank you for your reply. We check and have reply from RA Tech they say the Prime bolt will not fit VFC, also they never try too
A questo punto c'è una sola cosa da fare: chiedere di paragonare i due carrier, se sono simili al massimo basta mettere il nozzle vfc.